Panasonic Telephone KXTGA939 User Manual

Installation Manual  
Additional Digital Cordless Handset  
Model No. KX-TGA939  
Thank you for purchasing a Panasonic digital cordless phone.  
This unit is an additional handset compatible with the following  
Panasonic Digital Cordless Phones:  
KX-TG9391/KX-TG9392  
You must register this handset with your base unit before it can  
be used. This installation manual describes only the steps  
needed to register and begin using the handset. Please read  
the base unit’s operating instructions for further details.  
Charge the batteries for about 7 hours before initial use.  
Please read this installation manual before using the unit and  
save it for future reference.  
For assistance, visit our website:  
for customers in the U.S.A. or  
Puerto Rico.  
PNQX1455ZA DM0708SY0  
 
LThe AC adaptor must remain connected at all times. (It is normal for  
the adaptor to feel warm during use.)  
Battery installation and battery charge  
Important:  
LUse the supplied rechargeable batteries (Part No. HHR-55AAABU).  
LWhen installing the batteries:  
– Wipe the battery ends (S, T) with a dry cloth.  
– Avoid touching the battery ends (S, T) or the unit contacts.  
– Confirm correct polarities (S, T).  
LWhen replacing the batteries:  
– USE ONLY rechargeable Ni-MH batteries AAA (R03) size.  
– Do NOT use Alkaline/Manganese/Ni-Cd batteries.  
– We recommend using the Panasonic rechargeable batteries noted  
in the base unit’s operating instructions for replacement battery  
information.  
1 Press the notch on the handset cover firmly, and slide it in the  
direction of the arrow.  
2 Insert the batteries negative (T) end first. Close the handset cover.  
3 Place the handset on the charger for about 7 hours before initial  
use.  
Note:  
LIf the batteries are fully charged, but the operating time seems to be  
shorter, clean the battery ends (S, T) and the charge contacts with a  
dry cloth.  
3
 
Attention:  
A nickel metal hydride battery that is  
recyclable powers the product you  
have purchased.  
Please call 1-800-8-BATTERY (1-  
800-822-8837) for information on how  
to recycle this battery.  
Registering a handset to the base unit  
1 Handset:  
Lift the handset and press {OFF}.  
2 Base unit:  
Press and hold {LOCATOR} for about 5 seconds until the registration  
tone sounds.  
LIf all registered handsets start ringing, press the same button to  
stop. Then repeat this step.  
3 Handset:  
Place the handset on the charger.  
LContinue the operation even when the handset display shows  
Registering”.  
4 With the handset still on the charger, wait until a long beep sounds  
and w stops flashing.  
Note:  
LIf an error tone sounds, or if w is still flashing, register the handset  
according to the base unit’s operating instructions.  
Display language  
1 {MENU} i {#}{1}{1}{0}  
2 {V}/{^}: Select the desired setting.  
3 Press the middle soft key to save. i {OFF}  
4
 
Wall mounting  
1 Drive the screws (not supplied) into the wall.  
2 Mount the charger (A), then slide it down (B) and to the right (C)  
until it is secure.  
25.4 mm  
(1 inch)  
A
B
C
Screws  
(120 V AC, 60 Hz)  
Belt clip  
You can hang the handset on your belt or pocket using the supplied belt  
clip.  
NTo attach the belt clip  
NTo remove the belt clip  
5
 
For your safety  
To prevent severe injury and loss of life/property, read this section  
carefully before using the product to ensure proper and safe operation of  
your product.  
WARNING  
Power connection  
LCompletely insert the AC adaptor/power plug into the power outlet.  
Failure to do so may cause electric shock and/or excessive heat  
resulting in a fire.  
LRegularly remove any dust, etc. from the AC adaptor/power plug by  
pulling it from the power outlet, then wiping with a dry cloth.  
Accumulated dust may cause an insulation defect from moisture, etc.  
resulting in a fire.  
LUnplug the product from power outlets if it emits smoke, an abnormal  
smell, or makes an unusual noise. These conditions can cause fire or  
electric shock. Confirm that smoke has stopped emitting and contact  
the Panasonic Call Center at 1-800-211- PANA (1-800-211-7262).  
Installation  
LTo prevent the risk of fire or electrical shock, do not expose the product  
to rain or any type of moisture.  
LDo not place or use this product near automatically controlled devices  
such as automatic doors and fire alarms. Radio waves emitted from  
this product may cause such devices to malfunction resulting in an  
accident.  
CAUTION  
Installation and relocation  
LThe AC adaptor is used as the main disconnect device. Ensure that  
the AC outlet is installed near the product and is easily accessible.  
6
 
Battery  
LWe recommend using the supplied batteries or additional/replacement  
batteries noted in the base unit’s operating instructions for  
replacement battery information. USE ONLY rechargeable Ni-MH  
batteries AAA (R03) size.  
LDo not mix old and new batteries.  
LDo not open or mutilate the batteries. Released electrolyte from the  
batteries is corrosive and may cause burns or injury to the eyes or skin.  
The electrolyte may be toxic if swallowed.  
LExercise care when handling the batteries. Do not allow conductive  
materials such as rings, bracelets or keys to touch the batteries,  
otherwise a short circuit may cause the batteries and/or the conductive  
material to overheat and cause burns.  
LCharge the batteries provided with or identified for use with this  
product only, in accordance with the instructions and limitations  
specified in this manual.  
LOnly use a compatible charger to charge the batteries. Do not tamper  
with the charger. Failure to follow these instructions may cause the  
batteries to swell or explode.  
Other information  
LOperating the product near electrical appliances may cause  
interference. Move away from the electrical appliances.  
LUse only the power cord and batteries indicated in this manual. Do not  
dispose of batteries in a fire. They may explode. Check with local  
codes for possible special disposal instructions.  
Routine care  
LWipe the outer surface of the product with a soft moist cloth.  
LDo not use benzine, thinner, or any abrasive powder.  
7
 
Notice for product disposal, transfer, or return  
LThis product can store your private/confidential information. To protect  
your privacy/confidentiality, we recommend that you erase the  
information such as phonebook or caller list entries from the memory  
before you dispose of, transfer, or return the product.  
FCC and other information  
This equipment is hearing aid compatible as defined by the FCC in 47  
CFR Section 68.316.  
When you hold the phone to your ear, noise might be heard in your  
Hearing Aid. Some Hearing Aids are not adequately shielded from  
external RF (radio frequency) energy. If noise occurs, use an optional  
headset accessory or the speakerphone option (if applicable) when  
using this phone. Consult with your audiologist or Hearing Aid  
manufacturer about the availability of Hearing Aids which provide  
adequate shielding to RF energy commonly emitted by digital devices.  
WHEN PROGRAMMING EMERGENCY NUMBERS AND(OR) MAKING  
TEST CALLS TO EMERGENCY NUMBERS:  
1) Remain on the line and briefly explain to the dispatcher the reason for  
the call.  
2) Perform such activities in the off-peak hours, such as early morning or  
late evenings.  
This device complies with Part 15 of the FCC Rules. Operation is subject  
to the following two conditions:  
(1) This device may not cause harmful interference, and (2) this device  
must accept any interference received, including interference that may  
cause undesired operation.  
Privacy of communications may not be ensured when using this phone.  
8
 
CAUTION:  
Any changes or modifications not expressly approved by the party  
responsible for compliance could void the user’s authority to operate this  
device.  
NOTE:  
This equipment has been tested and found to comply with the limits for  
a Class B digital device, pursuant to Part 15 of the FCC Rules. These  
limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses,  
and can radiate radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful interference to  
radio communications. However, there is no guarantee that interference  
will not occur in a particular installation. If this equipment does cause  
harmful interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is encouraged  
to try to correct the interference by one or more of the following  
measures:  
– Reorient or relocate the receiving antenna.  
– Increase the separation between the equipment and receiver.  
– Connect the equipment into an outlet on a circuit different from that to  
which the receiver is connected.  
– Consult the dealer or an experienced radio/TV technician for help.  
FCC RF Exposure Warning:  
LThis product complies with FCC radiation exposure limits set forth for  
an uncontrolled environment.  
LThis handset may not be collocated or operated in conjunction with  
any other antenna or transmitter.  
LThe handset may be carried and operated with only the specific  
provided belt-clip. Other non-tested belt-clips or similar body-worn  
accessories may not comply and must be avoided.  
Notice:  
LFCC ID can be found inside the battery compartment or on the bottom  
of the unit.  
9
 
Compliance with TIA-1083 standard:  
Telephone handsets identified with this logo have  
reduced noise and interference when used with T-Coil  
equipped hearing aids and cochlear implants.  
Compatible with  
Hearing Aid T-Coil  
T
TIA-1083  
Notice  
LThis product is designed for use in the United States of America.  
Sale or use of this product in other countries may violate local laws.  
LCet appareil est conçu pour être utilisé aux États-Unis d’Amérique.  
La vente ou l’emploi de cet appareil dans certains autres pays peut  
constituer une infraction à la législation locale.  
LEste producto está diseñado para usarse en los Estados Unidos de  
América.  
La venta o el empleo de este producto en ciertos países puede  
constituir violación de la legislación local.  
Lҏ౰ࠢட
छ୽
ٺ
ҢՄ೩Ȅषӵ
ڏ
т୽ড়᎛୵
ٺܖ
ҢȂџ૖ོႂІ࿋  
Ӵ
ٽݲ
Ȅ  
L
ߩߎ
⵾ຠ
ޔߪ
ᣣᧄ࿖ᄖ
ߩߢ
૶↪
⋡⊛
ߡߒߣ
⸳⸘
ޔࠅ߅ߡࠇߐ
ᣣᧄ  
࿖ౝ
ߩߢ
૶↪
ߪ
ᴺᓞ㆑෻
ࠅߥߣ
߹
ޕߔ
ޔߡߞ
ᒰ␠
ߪߢ
ᣣᧄ࿖ౝ
ߦ
 
߅
ߪߡ޿
ේೣ
ߡߒߣ
ୃℂ
ࡆ࡯ࠨߩߤߥ
ߪ
ߨ߆ߒ
߹
ޕߔ
 
 
If you need assistance with setup or  
operation  
3 Call us at: 1-800-211-PANA (1-800-211-7262)  
TTY users (hearing or speech impaired users) can call 1-877-833-  
8855.  
When you ship the product  
LCarefully pack your unit, preferably in the original carton.  
LAttach a letter, detailing the symptom.  
LSend the unit to PSTC (Panasonic) Exchange Center, prepaid and  
adequately insured.  
LDo not send your unit to Panasonic Consumer Electronics Company  
listed below or to executive or regional sales offices. These locations  
do not repair consumer products.  
Panasonic Consumer Electronics Company,  
Division of Panasonic Corporation of North America  
One Panasonic Way, Secaucus, New Jersey 07094  
Panasonic Puerto Rico, Inc.  
San Gabriel Industrial Park, Ave. 65 de Infantería, Km. 9.5, Carolina,  
Puerto Rico 00985  
Copyright:  
This material is copyrighted by Panasonic Communications Co., Ltd.,  
and may be reproduced for internal use only. All other reproduction, in  
whole or in part, is prohibited without the written consent of Panasonic  
Communications Co., Ltd.  
© 2008 Panasonic Communications Co., Ltd. All Rights Reserved.  
 
Manual de instalación  
Auricular Inalámbrico Digital Adicional  
Modelo N° KX-TGA939  
Gracias por adquirir un teléfono inalámbrico digital Panasonic.  
Esta unidad es un auricular adicional compatible con los siguientes  
teléfonos inalámbricos digitales Panasonic:  
KX-TG9391/KX-TG9392  
Debe registrar este auricular con su unidad base antes de poder  
usarlo. Este manual de instalación sólo describe los pasos  
necesarios para registrar y comenzar a usar el auricular. Lea las  
instrucciones de operación de la unidad base para obtener mayores  
detalles.  
Cargue las baterías aproximadamente durante 7 horas antes de  
utilizarlas por primera vez.  
Lea este manual de instalación antes de usar la unidad y guárdelo para  
consultarlo en el futuro.  
Para obtener ayuda, visite nuestro sitio web:  
http://www.panasonic.com/help para clientes de Estados Unidos o  
Puerto Rico (Sólo en inglés).  
 
Accesorios incluidos  
Accesorio/Número de pedido  
Cantidad  
Cargador/PNLC1001YT  
1
1
2
1
1
Adaptador de corriente para el cargador*1/PQLV209T o PQLV219Z  
Baterías recargables*2  
Tapa del auricular*3/PNYNTGA430BR  
Gancho para el cinturón/PNKE1004Z1  
*1 Los dos adaptadores para corriente funcionan bien con el cargador.  
*2 Lea las instrucciones de operación de la unidad base para obtener  
información acerca de las baterías de reemplazo.  
*3 La cubierta del auricular viene unida a él.  
Nota:  
L
Lea las instrucciones de operación de la unidad base para obtener  
información acerca de los accesorios adicionales o de reemplazo.  
Información de ventas y respaldo  
L
L
Para pedir accesorios adicionales o de repuesto, llame al 1-800-332-5368.  
Los usuarios TTY (usuarios con impedimentos auditivos o del habla) pueden  
llamar al 1-866-605-1277.  
Conexión  
(120 V CA,  
60 Hz)  
Ganchos  
(2)  
 
     
Nota:  
L
L
Use sólo el adaptador de corriente Panasonic PQLV209 o PQLV219 incluido.  
El adaptador de corriente debe permanecer conectado todo el tiempo. (Es  
normal que el adaptador se caliente durante su uso.)  
Instalación y carga de la batería  
Importante:  
L
Utilice las baterías recargables que se suministran (N° de serie  
HHR-55AAABU).  
L
Al instalar las baterías:  
– Limpie los extremos de las baterías (  
– Evite tocar los extremos de las baterías (  
– Asegúrese de que las polaridades estén correctas (  
S
,
S
T
,
) con un paño seco.  
) o los contactos de la unidad.  
).  
T
S,  
T
L
Al reemplazar las baterías:  
– Utilice SÓLO baterías recargables de Ni-MH tamaño AAA (R03).  
– NO utilice baterías alcalinas, de manganeso o de Ni-Cd.  
– Le recomendamos que use las baterías recargables Panasonic que se  
especifican en la información de las baterías de reemplazo de las  
instrucciones de operación de la unidad base.  
1
2
3
Oprima firmemente el seguro de la cubierta del auricular y deslícelo en  
dirección de la flecha.  
Inserte primero el extremo negativo (  
auricular.  
T) de las baterías. Cierre la tapa del  
Coloque el auricular en el cargador durante aproximadamente 7 horas  
antes de usarlo por primera vez.  
(3)  
 
Nota:  
Si las baterías se cargaron por completo pero su tiempo de funcionamiento  
L
parece ser más corto, limpie los extremos de las mismas (  
S,  
T) y los  
contactos de carga con un paño seco.  
Cómo registrar un auricular a la unidad base  
1
2
Auricular:  
Levante el auricular y oprima  
{
OFF  
}.  
Unidad base:  
Oprima y mantenga oprimido  
{
LOCATOR durante aproximadamente  
}
5 segundos hasta que suene el tono de registro.  
L
Si todos los auriculares registrados comienzan a timbrar, oprima el mismo  
botón para detenerlos. Después repita este paso.  
3
4
Auricular:  
Coloque el auricular en el cargador.  
L
Continúe la operación aunque la pantalla del auricular muestre  
Registrando  
Con el auricular aún en el cargador, espere a que se emita un pitido largo y  
deje de parpadear.  
.  
w
Nota:  
Si suena un tono de error, o si  
de acuerdo con las instrucciones de operación de la unidad base.  
L
w
continúa parpadeando, registre el auricular  
Idioma de la pantalla  
1
2
3
{
MENU  
{V} {^}: Seleccione la configuración deseada.  
Oprima la tecla de función del medio para guardar.  
}
i
{#}{1}{1}{0}  
/
i
{OFF}  
(4)  
 
Montaje en la pared  
1
2
Inserte los tornillos (no incluidos) en la pared.  
Monte el cargador ( ) y deslícelo hacia abajo (  
que quede bien asegurado.  
A
B) y a la derecha (C) hasta  
25.4 mm  
(1 pulgada)  
A
B
C
Tornillos  
(120 V CA, 60 Hz)  
Gancho para el cinturón  
Usted puede colgar el auricular en el cinturón o bolsillo usando el gancho para el  
cinturón incluido.  
N
Para colocar el gancho para el  
cinturón  
N
Para quitar el gancho para el  
cinturón  
(5)  
 

Miele Freezer K 1803 Vi User Manual
Miele Oven H394B User Manual
MTD Snow Blower E173 User Manual
NETGEAR Network Router RT210 User Manual
Newcon Optik Laser Pointer LAM 10M IR User Manual
Nokia Network Router M5122 User Manual
NordicTrack Home Gym CTK65020 User Manual
Omnimount Computer Accessories WS 2 User Manual
Oricom Two Way Radio PMR1200 User Manual
Panasonic Battery Charger EY0110 User Manual